Share your ICND1 v3.0 Experience

9tut can you please update your site for ICND1 100-105.

Did someone passe the 100-105 ?? simulator you have ?

no mate. i am going to take exam in TEN Days time.

I took about one weeks ago the new ICND1 Exam 100-105 ; you can use old ICND1 Exam topic; not hard ; the SIM was similar to The Secuity Sim at https://www.9tut.net/icnd1/icnd1-security-testlet the 2nd Sims ; you need to know the concept of DHCP server ; and also NAT ( it was missing a Acceess-list that shows the corresponding traffic to go) . Make sure undertand How DHCP server works on the ROuter with exclcude address and also make sure your Scope is correct. No need to configure it just show commands.

@james Thanks for sharing your experience man much appreciated. The thing is though i am very scared because its my first time ever LOL

You can Email me djnada(at)99 yahoo. com

@James; Were the questions similar to previous dumps that folks have listed for review? Similar questions, not talking about the labs…

You have this one on ur ICND1?

Vidéo on this links are vers bad

Hello Friends, I Failed with 825, i had a 4 question of NTP, is easy but y I recommend you review the theme, these 3 of 4 question:
1- Which technology allows a large number of private IP addresses to be represented by a smaller number of public IP addresses? (Answer NAT)
2- Which NTP command configures the local device as an NTP reference clock source?(Answer NTP)
3- Which device allows users to connect to the network using a single or double radio?(Answer Access Point)
-The 3 question of momo also:
Which MTU size cause a baby giant error ?? answer ??
which RFC was created to alleviate the depletion of IPVA4 pulic adresse ??
which entity assigns IPV6 addresse to end user?
the labs:
-Security Testlet same scenary but more hard, ( you review totaly the class)
-lab with ACL, NAT (loopback), and NTP (sorry but i dont remember la scenary only the themes)
-One question of eigrp but very easy (“AD eigrp 90”)
NOTE: if using the information of this web you will insure exam 60% some questions of 100-101 remain.
finally ignore the links of bad users who lie and offer books, DON´T BUY those books. if somebody have more questions please share with the comunity

Thanks for the information dude! and I´m so zorry 🙁
I will take the exam tomorrow.. thanks again!!

MTu size= 1600? Or other 9400
Rfc= 1918
Entité assigné =isp
On ur lab you have dhcp 3 routeur and acl?
Did you configuré somehing or Just show command
Thank u Ricci i failed it me too twice one With thé 100-101 and other With 100-105
But m’y remake if u make some test like icnd1_icnd2_july_2015 u have false answer like thé 3 i vive thé answer
Çan u try more définit ur lab please

Ntp question answer Ntp server and no master

rfc 1918 are private or not??

Sorry ntp master and no server (www.pearsonitcertification.com/articles/article.aspx?p=2141272 )

True answer are 1918 and no 1518

For ur Nat the answer is not Nat but overloading

Ricci it looks like this? The lab
https://www.ciscomadesimple.be/2013/04/08/configuration_dhcp/#more-877

@momo I have question, in exam we have to configure or only uses show command for sims questions?

On 100-101 and 100-105 only show command.. on 200-101 show command on 200-105 i dont know

For ur Nat the answer is not Nat but overloading for which question ?

@momo

-lab with ACL, NAT (loopback), and NTP

Anyone have ideas about above labs for ICND1 exam? I mean what kind of questions they asked in exam?

Thank you.

guys attention…. i was reading and rfc to ipv4 publin is 1518
and which entity assigns IPV6 address to end user is RIR…. CORRECTME IF IM WRONG BUT I INVESTIGATE THAT

No RIR.

Answer: ISPs.

I bring to you a PDF that has surprisingly several of the questions that came to me though are ccna, I came in the ICND1 100-105, I share it with the condition that the person take the test share a real experience of it and confirm questions.

https://mega.nz/#!0xlkhTIA!5pqm4Pb1OtehwIkwWkc6QcfL9uYITATaNTO3CQTbL24

Thanks a lot @Ricce21

@Ricce21 I can’t download the PDF
Please share on a different link

Current simulation we’ve heard of so far are
1)ACL
2) DHCP
3)NAT

Any others?? Only commands required are “Show”

Anyone with the current ICND1 v3.0 dumb on PDF ???

I pass it…
Same hospot and all the question we talk about.
Same as 100 -101, for thé simulation si 1 routeur isp connected with router r1 , r1 connected to router 2 and is the dhCP serveur connect to router 3 dhcp client.
1 question about dhcp client nô receive ip
1 question about ntp r2 no réceive ntp
1 question about Nat on r1 or r3 configuréd or notre
1 question about acl ..client no have internet.

Hotspot is thé dame.
Rfc 1918
Non ror
Switch on thé sa me broadcast

Succèss ur simulation and hotspot u succed thé 100-105

@momo congratulations
“Hotspot dame” ?

Anyone have the ICND 1 100-105? share please i need your help

thankyou

waltercorona60 gmail.com

Yes understand the dame hotspot ande understand commande on simulation dhcp Nat ntp acl

No dame sorry but same as un have here on 9tut

Excuse me, but what is a ”
hotspot dame”

I would like to share the 2 books, if anyone is interested.

https://drive.google.com/open?id=0B6mnbxOlbXoxVlk1RGVtemZ0dU0

Do not take exam now!!! Wait until new material from 9tut…..all new material on V3.

@momo

Congratulations…..:)
Can you explain QUESTIONS about DHCP, NAT, NAP AND ACL ?

Thank you.

for thé simulation si 1 routeur isp connected with router r1 , r1 connected to router 2 and is the dhCP serveur connect to router 3 dhcp client.

which one can you explain?

@momo

For simulateur you have 4 question 1 answer by question
1. You must see on router 2 (server) and routeur 3 (client) if dhcp are good.
2. You must see on routeur isp or routeur 1 if ntp have thé good paramètre : symbole ? No Work
3. You must see on routeur 1 or routeur 2 or 3 if thé paramètre on Acl are good for let People to use internet
4. you must see on routeur 2 or 3 if nat are good

You must Know command to débug or see paramètre acl, paramètre dhcp or acl or nat. The symbole ? No Word
Now i tell you thé very must difficult

Thank you @momo

Hey guys… i take exam 100-105 i´m sharing with you some question that i remember from exam

Which RFC was created to alleviate the depletion of IPv4 public addresses?
A.
RFC 4193
B.
RFC 1519
C.
RFC 1518
D.
RFC 1918

Which value is indicated by the next hop in a routing table?
A.
preference of the route source
B.
IP address of the remote router for forwarding the packets
C.
how the route was learned
D.
exit interface IP
address for forwarding the packets

Which entity assigns IPv6 addresses to end users?
A.
ICANN
B.
APNIC
C.
RIR
D.
ISPs

Which statement about routing protocols is true?
A.
Link state routing protocols choose a path by the number of hops to the destination.
B.
OSPF is a link state routing protocol.
C.
Distance vector routing protocols use the Shortest Path
First algorithm.
D.ISIS is a distance vector routing protocol.

someone can resolv it?

1) D
2) B
3) D
4) A

CAN PLEASE SHARE SIM AND CONFIGURATION QUESTION FOR US?

THANK YOU:)

@9tut when are you going to update this site for 100-105????

Hi everyone,

I am going for ICND1 next week I need help from someone to tell me what exactly to be focused on. The books is too long to go over it.

Thanks

h t t p : / / w w w . g r a t i s e x a m . c o m / all question from this website but be careful some answer are wrong

Security Testate find any good website don’t use 9tut for this question

https://mega.nz/#!0xlkhTIA!5pqm4Pb1OtehwIkwWkc6QcfL9uYITATaNTO3CQTbL24 use this one

Also they asked about DHCP but I don’t know correct answer for this question

I am reading that new book, CCENT/CCNA: ICND1 100-105 Official Guide. It’s big and boring. I take the exam in five days but ordered another book. Sounds crazy but that’s the situation with the new contents added to the exam. Sounds challenging..

Hello Guys,

I think this material can help you! Please confirm how took the exam https://1drv.ms/b/s!Ahr_jHbUQ0JjlWqNXQQlfbRkBfET

Two hosts are attached to a switch with the default
configuration. Which statement about the configura
tion is true?
A. IP routing must be enabled to allow the two hosts
to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allo
w the two hosts to communicate.
D. Port security prevents the hosts from connecting
to the switch.

Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518

Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the n
ative VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by de
fault.
C. Control plane traffic is blocked on the native VL
AN.
D. The native VLAN is typically disabled for securit
y reasons.

PLEASE, any one:

For while, I have ” google_ed ” for application to convert pdf to VCE ( exam )

Thanks!

the Lab was very easy! only do show command and you will know what they ask, just thing about new questions guys shared here, and more of them, I saw only one subnetting question 2-simulate and 5 multiple choices.

NAT has two IP address on WAN site,
PC in LAN router B cannot connect to router A.
DHCP problems.
Router C cannot get DHCP from router B,
__________________________> ACCESS LIST-NAT-DHCP-PORT CONFIG

Two hosts are attached to a switch with the default
configuration. Which statement about the configura
tion is true?
A. IP routing must be enabled to allow the two hosts
to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allo
w the two hosts to communicate.
D. Port security prevents the hosts from connecting
to the switch.

B–correct

Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518

D–correct source: www. cicso .com c/en/us/support/docs/switches/catalyst-4000-series-switches/29805-175.h t m l

Dear CISCOTTE.
Don’t west your time for that just find some pdf

Hello everyone. I had no idea that icnd1 has updated to 100-105 so I studied the old 100-101 Cert guide from Wendell Odom. Can anyone tell what is extra in this new cert guide? because I don`t want to read the whole book.
Thank you.

Ron jones
lot of bad answer onthis PassLeader 100-105

IF YOU SAY SO Mr. momo:

PLEASE – Don’t leave people in the DARK!!!!

What are the number ( # ) of the WRONG questions on the PassLearder 100-105

* PEUT-ÊTRE SERAIT IL MIEUX DE LIRE LE TEST EN ANGLAIS ?????

Thanks!

As i tell on my old comment, rfc1518, vlan 1, baby gant and other

Dear memo, these all are not correct or correct??????

Does anybody know when 9tut is going to UPDATE the site for the new exam????

Is it still worth using the Practice Exam 9tut provides?

hi guys, I bring to you one:

Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco
D. SwitchCisc0

really this is a one question

@Ricce21
Answer: C

D is correct

Sorry, C is correct

I’m zorry but I don’t understand, all names is correct.
Why the answer is C?
I tested with packet and GNS3 and all work.

hmmm…. or maybe it’s a gift question of cisco

other question:

Which two characteristics describe the access layer of the hierarchical network desing model?
A. layer 3 support
B. port security
C. redundant components
D. VLANs
E. PoE

I say A-B, What do you think.

I think is B and D, it’s definitely not A and is super easy to tell that, the core is the one who provides layer 3 support.

@Ricce21 about access layer:
the answer is A,E
see :http://www.ciscopress.com/articles/article.asp?p=2202410&seqNum=4

oups sorry B,E
according the link http://www.ciscopress.com/articles/article.asp?p=2202410&seqNum=4

B and E

B D Sir

B-D,
PoE also is, but Vlans is more general, all switches support VLANs, PoE only specific, my friend CCNP me explain this.

Next:
Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require
outside access

@Ricce21
Answer: B

Anyone have idea about DHCP sim? How to solve?

Answer port security and vlan other answer b

Jean Claude Van Damme, thank you so nuch. Have you got a book ICND2 200-105?

the question of baby giant:

Standard Ethernet frame MTU is 1500 bytes. This does not include the Ethernet header and Cyclic Redundancy Check (CRC) trailer, which is 18 bytes in length, to make the total Ethernet frame size of 1518. In this document, MTU size or packet size refers only to Ethernet payload. Ethernet frame size refers to the whole Ethernet frame, including the header and the trailer. Baby giant frames refer to Ethernet frame size up to 1600 bytes, and jumbo frame refers to Ethernet frame size up to 9216 bytes.

http://www.cisco.com/c/en/us/support/docs/switches/catalyst-4000-series-switches/29805-175.html

@Momo

How did you solve DHCP in exam?

Please can you help me.
Thank you.

of course @RUS

https://drive.google.com/open?id=0B6mnbxOlbXoxWnZtZTl6bzBnNVU

regards Sir

Which statement about routing protocols is true?

A. Link-state routing protocols choose a path by the number of hops to the destination.
B. OSPF is a link-state routing protocol.
C. Distance-vector routing protocols use the Shortest Path First algorithm. D. IS-IS is a distance-vector routing protocol.

Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518.

Answer: C is correct,

Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?

A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Hello all, i would like to thank everyone for posting usefull iinformation and files…It helps a lot studying for ICND1.

A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

B is correct.
Explanation: switch dont do routing, VLAN is only needed to break broadcast domains, port security is disabled by default and you only use it for blocking/logs port use attempt

One for you guys….

After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch?
A. The POST was successful.
B. The switch has a problem with the internal power supply and needs an external power supply to be attached.
C. POST failed and there is a problem that prevents the operating system from being loaded.
D. The switch has experienced an internal problem but data can still be forwarded at a slower rate.
E. The switch passed POST, but all the switch ports are busy.

Correct: C

thanks pl
I knew 2nd option is correct but one french website share that the first option is correct and next I got confused about this question. really can’t believe to any website

Jean Claude Van Damme, thank you, bro!

Hi everyone,

I did a lengthy research and the answer to the question below is actually D, one-way NAT is basically PAT.

Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require
outside access

https://learningnetwork.cisco.com/thread/63452

guys, anyone has taken the exam … update ..

@pass and @Pl413r
Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Answer: A

Hello this is the updated DHCP and RIPv2. with complete running configs.
https://drive.google.com/open?id=0B9XjqInn_2WiWFpNeG83M3AtdDg
password is pineapple.

ICND1

Switches don’t read IP addresses. They read Mac addresses. When you say A is correct could you also explain as well.

Same asked DHCP in ICND1 100-105