Share your ICND1 v3.0 Experience

Hum ok , do you remember the question on sims?

Sims are the same as on this site. RIP2, DHCP

But you said you got different questions no?

Oh ok nvm

Do you got one of this

Did you have those
Which protocol provides best-effort delivery of user data in a network?
If NVRAM lacks boot system commands where does the router look for the cisco ios by default
WAN Data link encapsulation types include which of the following
Which of the following commands enables a network admin to verify the application layer connectivtiy between devices
What 8-bit field exists in IP packet for QoS
Which of the following are found in a tcp header but no in a udp header
Which transport layer protocol is best suited for the transport of VoIP data

@Certking What was the command line question?

Are there VLSM questions?

@Jolie , can you provide 370q i have exam soon pls

I think Gareth needs some real study time. If you cant go learn what the different cable types are, you have no business even trying for CCNA

@Anonymous i know cables

10BASE-FX= fiber
10base5=coaxial
100BASETX=twisted

But i cant understand the goal of including usb cable , there are not in IEE norms

@Jolie could you please share the valid dumps for 200-105?

Hello All,

Yesterday tried to pass the test for the first time. I got 812 of 832 unfortunately. The drag and drop question has to do with ehthernet type(100base FX ,TX etc) and with what kind of type(inshielded twisted pair,etc). Also remember a question about CEF, and a question about the MTU size when on 802.1q. About the SIMS ,the security testlet and the DHCP sim fell to me but with different answers as the appeared issues was different from the files provided here. I downloaded the 351 dumb file from Jolie,is there any newest file that someone can share? From the total 54 questions i think almost 20 saw for the first time. Any help woulb be much appreciated.

@ gareth, do you remember the full cabling question? I got it and it confused me

@thomas

The question about cef was about which components is used With it ?
The mtu on trunk need to add 4byte

FX=fiber
TX =twisted
10base-2=coaxial

Did you have question about firewall , dns . Syslog and full mesh?

So the question was about matching fiber twisted to 100baseFX and so on ?

@Gareth,

Yes regarding the “matching fiber twisted to 100baseFX and so on”

I had a question for the Bus topology,regarding the Syslog dont remember exactly the words but was for message 6 syslog.

For the CEF i think the question was “What disables CEF” and found that question from the 351dumb but didnt found the others questions

@Gareth

Also had questions for DNS but dont remember exactly

@Thomas DNS question was : how to tshoot dns ?

Syslog was : Level of message sent by défault (0-6)?

What was the question about bus ?

Did you remember the other câble type ? Coaxial fiber twisted and ?

Check the question I posted above , did you get one of those ?

You have to match them,
Twisted>>>>10/100/1000mbs
Fiber>>>>>>BASE-BX
Coaxial>>>>Bases

Coaxial is only BASE2 and 5 right ?

CEF is disabled by ACL Logging

Here olsa have topology
Bus star …I dont remember but here say one another or something
Olsa have syslog questions 2.
Say here level 0 6 and e.

@Vugo , what syslog question are you talking about ?

hi

Certking’s right…new stuff.
maybe 15 qs from 9tut
and 9tut mosdef is helpful but is not up to date w new qs.
study…study and

….study

@gareth Syslog was : Level of message sent by défault (0-6)?

@ogee did u pass?

@vugo yes thats it.

What was the question about bus ?

Do you remember the other question ?

@Gareth

Do you remember the exact question?

@anon which one

@gareth

the cabling question with the fiber and the other ones, sorry but my memory is shot right now. I’m sitting the exam in afew days so i will report back with feedback

No sorry. Maybe other people know it

Question for everyone –
Which set of conditions comprises a successful ping attempt between two connected routers configured with IP addresses on the same subnet?

A. The destination host receives an echo reply from the source host within one second and the source host receives an echo reply from the destination
host within two seconds.

uhmmm what? It should be.

The destination host receives an echo request from the source host and the source host receives an echo reply from the destination host within two
seconds

Hello , I’m taking the exam tommorow , can people give me more details about the new questions you are talking?

These are new questions gathered from our candidates’ reports.

Question 1

Syslog – what does not belong: host name , severity, timestamp, message

Question 2

What does a switch use for communication between VLANS: answer is VTP

Question 3

Maximum MTU for ethernet when doing 802.1Q : 1522

Question 4

When configuring a default gateway, should it be ip route 0.0.0.0…. or serial 0/0 0.0.0.0…… – dont know answer

Question 5

What is 0.0.0.0 address – gateway of last resort, default gateway, null address. i think its default gateway

Question 6

What is the purpose of a standard access list – to filter traffic based on destination address; to deny traffic…i wasn’t sure if standard ACLs filter or deny

Question 7

If you are in VLAN 10 and it gets a packet from VLAN 2 with 802.1q enabled, what does it do with the packet? Drops the packet ; forwards it to VLAN 2 ; configures the port to handle traffic from VLAN 2 ; adds it to the VLAN database…I wasn’t sure

Question 8

Drag drop question about cable types

Answer:

Coaxial
Twisted 10/100/1000 Mpbs
Fiber BASE-BX

For syslog , hostname does not belong to message

@ezad you pass exam ?

yes

Question 1
Syslog – what does not belong: host name , severity, timestamp, message

What answer this ?

@ezad Question 8
Drag drop question about cable types

Here olsa have usb cabel

Hostname I guess
Hum i didnt have usb cable , what was the usb cable choice?

I choose answer device for TV connection

Coaxial is for TV connection

What were the other choices u had?

@ezad What you choices answer this questions ???

Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518
Answer:?

3.Which RFC was created to alleviate the depletion of IPv4 public addresses?
A. RFC 4193
B. RFC 1519
C. RFC 1518
D. RFC 1918

1518 for both

@Vugo what were the other choices you had during the drag and drop?

@ezad Syslog was : Level of message sent by défault (0-6)?

what answer this ?

And you pass which score ?

0-6

912

What were the other choice u had during drag and drop?!

is it 1600 for baby giant error?

10/100/1000 Mpbs
TV connection
BASE-5 BX
BASE 10 TX

another I dont remember

@R Which MTU size can cause a baby giant error?
Which RFC was created to alleviate the depletion of IPv4 public addresses?

This questions answer nobody says right.Also I dont know which answer is right…How help for this questions answer ?

10BASE-5 BX does not exist

Tv connection = coaxial
10/100/1000 = twisted

TX=Twisted

FX=fiber

@vugo,

I’m pretty sure the answer is 1600 for baby giant error.

If the default is 1500, then `>1500 but less than 1601 ( I put the 1601) would be a baby giant.

If the default is 1518, then >1519 but less 1601 would be the baby giant.

For alleviate depletion it should be 1518.

@ezad thansk for explained

I dont know why you mentioned usb cable @vugo

These might also help..

IEEE 802.3u – 100Base-Tx
IEEE 802.3 – 10Base-T
IEEE 802.3ab – 1000Base-T
IEEE 802.3z – 1000Base-SX

10Base-T (IEEE 802.3) 10 Mbps using category 3
unshielded twisted pair (UTP)

100Base-TX (IEEE 802.3u) 100Base-TX, most
commonly known as Fast Ethernet

100Base-FX (IEEE 802.3u) Uses fiber cabling 62.5/125-
micron multimode fiber.

1000Base-CX (IEEE 802.3z) Copper twisted-pair, called
twinax, is a balanced coaxial pair

1000Base-T (IEEE 802.3ab) Category 5, four-pair UTP
wiring up to 100 meters long and up to 1 Gbps

1000Base-SX (IEEE 802.3z) The implementation of 1
Gigabit Ethernet running over multimode fiber-optic cable

@ezad because here choice answer have also usb cabel

Ok , with what did you match usb cable?

10BASE-5

Hum I think 10base-5 is for Coaxial

Ok , with what did you match TV connection cable?

Coaxial too

it was in 2 different question for me

You had to match coaxial with speed and use in the same question?

which questions ?

I had one question with

Fiber – coaxial and twisted pair and I need to match speed

One other with fiber coaxial twister and match their uses

Not you?

Question 6 – standard acls filer by source address I believe

Yes , I had a question on how firewall work too

Question 7 – I think it would drop the packet?

yep i think too

@Vugo how many choices did you had on the drag and drop

Kinda confused on question 4 & 5. Default gateway would be the ip address on the router. If you configured it on a switch you would use the up default-gateway command.

Ip route 0.0.0.0 would be used for setting the gateway of last resorton a router, so I would assume 0.0.0.0 address would be gateway of last resort or maybe null address depending on what the question is asking

Is 351q by Jolie still valid for study?

@Xcessive , yea the question is weird

Default gateway will be on L2 devices
Default route on L3

Right?

Yes I believe that is correct

The drag and drop question is weird too

Which of the following are found in a TCP header but not in a UDP header

Someone got this one?

What is 0.0.0.0 address – gateway of last resort, default gateway, null address. i think its default gateway

If its in the ip route command –> default gateway

Or null adress

What would you say?

ip route 0.0.0.0 0.0.0.0 = gateway of last ressort

@ezad

It might be the question for it.

@ezad

Which of the following are found in a TCP header, but not in aUDP header?
(Choose three)
A. Checksum
B. Sequence number
C. Destination port
D. Window size
E. Acknowledgment number
F. Source port

Answer: B, D and E

UDP only contains four.

Source port number (2 bytes)
Destination port number (2 bytes)
Length of data (2 bytes)
UDP checksum (2 bytes)

Is this a new question?

Question 1

Syslog – what does not belong: host name , severity, timestamp, message

Hostname , right ?

Yes hostname should be right

Question 2

What does a switch use for communication between VLANS: answer is VTP

Hum i would say L3 devices right?

Or VTP to propagate vlan

@ezad

You are right.

VLAN communicate in Switch if it is a Layer 3. It allows encapsulation since it is a combination of Router and a Switch.

IF it is a Layer 2 Switch then it requires router on a stick to communicate to different VLANS.
We create encapsulation on the serial interface on the router so it will became the default vlan route that allows communication to different VLANS.

Just correct me if I an wrong.

Yea you are right

I dont understand the question above , weird question

hmmmm, I think it talks about VLAN on two Switches and it can communicate using VTP (Virtual Trunk Protocol)

Hum but switches dont communicate with VTP..

Which two statements about syslog loging are true?(Choose two.)

A. Syslog logging is disabled by default
B. Messages are stored in the internal memory of device
C. Messages can be erased when device reboots
D. Messages are stored external to the device
E. The size of the log file is dependenet on the resources of the device

Answer is B,C right?

A & D

Hum syslog is enabled by default for sure

Just type show logging on pkt

When troubleshooting client DNS issues, which two task must you perform? (Choose two)
A. Ping a public website IP address.
B. Ping the DNS Server.
C. Determine whether a DHCP address has been assigned.
D. Determine whether the hardware address is correct.
E. Determine whether the name servers have been configure

A & B …. hmm I’ll have to look at Syslog then, but I think logging part of it is for external device and needs to be enabled

You would need to use the logging host command to enable logging to external server.
Exp: logging host 192.168.11.101
Logging traps 5

So B and C are correct ?

For the DNS question dumps say B and E

For the syslog question I think A & D are correct. Syslog logging is for sending to an external server and it is not enabled by default. You have to use the logging host command with up address of syslog server to enable.

The dumps I have from how2pass are saying A & B for dns question