Share your ICND2 v3.0 Experience

@CCNA for 3 more years
Well said man,
I believe that if you only use dumps to pass, you will end up failing many times as you will not learn so much nice stuff that you will for sure need for you entire career. So dont waste your time and money!

@all can we all conc on brainstorming and share ideas pls. we need to stop advising others about depending on dump for success.

What is the technical answer to the following. . . .

How can you disable DTP on a switch port?

1. Change the administration mode to Access
or
2. Configure the switch port as a trunk

Any help would be great thanks.

I also have a question where I am getting conflicted answers:

Which statement about QoS default behavior is true?

A. Ports are untrusted by default.
B. VoIP traffic is passed without being tagged.
C. Video traffic is passed with a well-known DSCP value of 46.
D. Packets are classified internally with an environment.
E. Packets that arrive with a tag are untagged at the edge of an administrative domain.

Anyone know the correct answer?

@Jim

Port are untrusted by default

@pete
change the admin mode to Access

Hello,

Can anyone please share latest dumps.

Thanks

New Question.

What kind of data message is send to elect the root bridge
A. BPDU
B. Segment
C. Packets
D. Hello

Answer. A

@Pete
I tought it was 1 but my teacher said it is 2. Configure the switch port as a trunk. Which makes sense. Since according to him DTP wont go off if you change admin mode to access.

@Jim
Which statement about QoS default behavior is true?
A. Ports are untrusted by default.
B. VoIP traffic is passed without being tagged. X (i see it everywhere and i beleive its the right one)
C. Video traffic is passed with a well-known DSCP value of 46.
D. Packets are classified internally with an environment.
E. Packets that arrive with a tag are untagged at the edge of an administrative domain.

@Jim
Explanation/Reference:
Frames received from users in the administratively-defined VLANs are classified or tagged for transmission to
other devices. Based on rules that you define, a unique identifier (the tag) is inserted in each frame header
before it is forwarded. The tag is examined and understood by each device before any broadcasts or
transmissions to other switches, routers, or end stations. When the frame reaches the last switch or router, the
tag is removed before the frame is sent to the target end station. VLANs that are assigned on trunk or access
ports without identification or a tag are called native or untagged frames.
For IEEE 802.1Q frames with tag information, the priority value from the header frame is used. For native
frames, the default priority of the input port is used.
Each port on the switch has a single receive queue buffer (the ingress port) for incoming traffic. When an
untagged frame arrives, it is assigned the value of the port as its port default priority. You assign this value by
using the CLI or CMS. A tagged frame continues to use its assigned CoS value when it passes through the
ingress port.

New Qs Download here
We are best Real Queation-Latest-Valid

Instant DOWNLOAD after checkout:
https://docs.google.com/document/d/1cp2vtCYSV_21JTZF9D14Ua2gHdijtZjfIDuyVT1NyJg/edit?usp=sharing

Hi guys, is ICND 2 much harder then the 1st exam ? also has anyone got some decent dumps for revision.

Use to use examocollections, now cisco is off that, someone post/link me the new dump for 200-105 the most recent and valid thank you 🙂

izt advisacomine icdn1 and icdn 2 once?

sorry,is it advisable to combine ICDN 1 and ICDN 2 ones,please advise and the possible ways to pass the exam

Passed ICND 2 today, I would advise using this website to study questions and CBT Nuggets to study concepts. Sims on the website are very similar, and are very helpful. You may encounter a few questions you may not be ready for on the exam but if you dedicated a lot of time to this website you will be fine. Thanks 9tut.

Anyone who has taken the icdn2 v3 exam seen any frame relay questions??? I thought they excluded them from the exam. Thanks in advance!

How does a router handle an incoming packet whose destination network is missing from the Routing table?
Does it discard the packet or route the packet to the default route??

@ aok. Both is correct based on the scenario. If there is a default route, it will forward it to the default route but if no default route then packet will be discarded

is ICND 2 much harder then the 1st exam ? also has anyone got some decent dumps for revision ?
thanks guys 🙂

@ pal. Icnd2 Is much more harder

Note: By default, all ports are in the untrusted state when QoS is enabled.

http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/24055-173.html

hi all anyone took the exam this week are the questions coming from the 9tut ? please reply i have exam soon
thank you

Hey Everyone,

I have been combing this site and forum for three last three months. I took the Test Wednesday and passed in the low 900s. Used the Odom book to read and study the fundamentals, but put all my faith in the Adjusted .VCE file frm NEB. I had all the same posted SIMs, just variations that weren’t hard to figure out. Only saw two questions that I had never seen before and I am sorry that I do not remember them.

I want to thank NEB for putting that together and everyone here for all the information and discussion.

Good Luck, everyone!

@Shadow Lurker

which .VCE file did you use? can you provide the link?

thanks

Hello,

I gave my exam yesterday and cleared it. I could see most of the questions from 9tut. Simulations are also same but the configuration is bit modified.

Thanks

I cleared my ICND1 today.. and I am thing to go forward to 200-105. if anyone has the recent dumps. please share with me, I would be thankful to you.

today 200-105 succed with 9XX . 95% of questions are here. same labs . gl everyone

Guys can anyone tell me what commands you used for the simulations please?

show running-config
show ip route
These are enough for simulations

@H@rry, thank you man. What resources did you use to study other than 9tut? Did you use that adjusted vce file? (aka icnd2.pdf).

@Jim
I’m correcting myself!
Which statement about QoS default behavior is true?
A. Ports are untrusted by default.X (i see it everywhere and i believe is the right one)
B. VoIP traffic is passed without being tagged.
C. Video traffic is passed with a well-known DSCP value of 46.
D. Packets are classified internally with an environment.
E. Packets that arrive with a tag are untagged at the edge of an administrative domain.

@tre1972
I went through that icnd2.pdf and it has bunch of correct ICND2 questions…
I found some real lab questions here too, hope it helps
demo.examkiller . n e t /PQA/DEMO-200-105.pdf

use icnd2.pdf is good enough
you have to know the routing protocols OSPF / EIGRP

no netflow questions for me

Thanks

what cann couse two OSPF neigbors to be stuck in the EXSTART state ?
A. there is a low bandwidth conections between neighbors
b. the neigbors have diferent MTU settings
c. The ospf interfaces are in Passive state
d. There is only layer one conections between neighbors

what do you people think aboute this one ?

b. the neighbors have different MTU settings

@Everyone who took the test…
I would appreciate it if you could tell us if you remember about questions related to:
1- HDLC IP Address?
2- Layer 2 attacks?
3- GLBP Benefits?
4- VRRP?
5- Proxy Arp?
6- HSRP IP Address
7- MD5
8- MAC/DHCP Spoofing?
9- HSRP?
10- IPSec?

Thank you in advance!

Hi all
Is this questions on the right side (ICND2 200-105) still valid?

Hi there, I have a general question: Which is a recommended braindump seller for cisco? Lately all of them seem to outperform each other with the amount of questions they sell – but then the dumps always contain ancient stuff.

hey guys. can you please share the link to the eigrp questions for the lab..

@ssh
no need to buy it!
donload it from here…adjusted_vce and icnd2.pdf
http://www.dropbox.c o m /sh/2imx6rougqnla2z/AAAMR_KERfE6fEJy0GYILEQYa?dl=0

@ssh
no need to buy it!
donload it from here…adjusted_vce and icnd2.pdf
w w w .dropbox. c o m /sh/2imx6rougqnla2z/AAAMR_KERfE6fEJy0GYILEQYa?dl=0

@9tut: can you please update the pdf for ICND 1&2 Questions and Answers?

https://www.9tut.net/icnd1-2-questions-and-answers

Thanks!

Hey Guys, I feel like I am drowning in a sea of information and resources. I am thankful for this information, but if you had to choose only a few sources (incd2.pdf/adjusted_vce/9tut_questions) what would you use. I know many questions show up in several different places and I am not trying to be lazy or looking for shotcuts as I have read the Cisco Press book and watched the CBT nuggets series. Thanks for any advice that can be given!

Which interface counter can you use to diagnose a duplex mismatch problem?
A. no earner
B. late collisions
C. giants
D. CRC errors
E. deferred
F. runts
B or D????
Thanks

@SW The adjusted_vce and icnd2.pdf are the same information in different formats….study the pdf if you don’t know how to work with the vce.

B. late collisions

@s3xs1 Thanks!

R1 and R2 cannot form an OSPF neighborship. What is the problem?
A. The area IDs of R1 and R2 are mismatched
B. Ethernet0/1 of R1 is configured with a non-default OSPF hello interval
C. The Layer 2 encapsulation of the serial links is mismatched
D. The OSPF hello and dead interval are mismatched

Answer: B

Explanation

Continue checking their connected interfaces with the “show running-config” command:

R1#show running-config
<>
!
interface Ethernet0/1
description **Connected to L2SW**
ip address 10.10.230.1 255.255.255.0
ip ospf hello-interval 25
ip ospf 1 area 0
!
<>
R2#show running-config
<>
!
interface Ethernet0/1
description **Connected to L2SW**
ip address 10.10.230.2 255.255.255.0
ip ospf 2 area 0
!
<>

B or D?

Also ,
Which statement about DTP is true?
A. It uses the native VLAN.
B. It negotiates a trunk link after VTP has been configured.
C. It uses desirable mode by default.
D. It sends data on VLAN 1.
A or D
Thanks !

@tubik,

I believe the answer is A

@tubik
Which interface counter can you use to diagnose a duplex mismatch problem?
A. no earner
B. late collisions
C. giants
D. CRC errors
E. deferred
F. runts

Every time I’ve dealt with duplex mismatch it has always been CRC errors that point it out. This is obvious to those of us that have auto-configure duplex on a switch to switch port and watch the counters. Sometimes they just don’t play nice and one ends up half, while the other is full duplex. Root cause is almost always a cable issue.

Don’t take my word for it, just look up the difference for what causes late collisions and CRC errors. You can also manually configure switch-to-switch ports with one at half duplex and the other set to full to see the fireworks.

Hi Paul
I know icnd2 200-105 is very hard but if you want you can take study from me on skype –you sent me reply here then i give you my contact.
thanks

Hello everyone i need the last dump of icnd 2 and valid

B. late collisions => https://learningnetwork.cisco.com/thread/9791

D. It sends data on VLAN 1. => https://learningnetwork.cisco.com/thread/89006

Thank guys !

Hello everyone i need the last dump of icnd 2 and valid

can any one send me the packet tracer files for gre simulation

please post gre multilink packet tracer files

Someone has dumpa for data center?

Which statement about slow inter VLAN forwarding is true?
A. The VLAN is experiencing slowness in the point-to-point collisionless connection.
B. The VLANs are experiencing slowness because multiple devices are connected to the same hub.
C.
The local VLAN is working normally, but traffic to the alternate VLAN is forwarded slower than expected.

D.
The entire VLAN is experiencing slowness.
E. The VLANs are experiencing slowness due to a duplex mismatch.

Any thoughts about this one? I am between E and C.

hi All how many simulations should i expect on the icnd2 exam

guys… Anyone please post the link for gre simulation packet tracer files.

Hello everyone!
I appeared for ICND 1 (100-101) a year back and planned on giving ICND 2 (200-101) this time but now the course code and maybe the content has changed.
Is there any big difference between the course content because I had Jeremy’s video lectures for 200-101, are they still valid?
Thanks.

@Sam new topics were added to the curriculum and some were removed from the 200-101 to the 200-105…I highly suggest getting updated study material…Also you might want to check into if you can mix 100-101 and 200-105….I don’t believe you can… you’d have to retake the new icnd1 exam.

@ER Lu

Thank you for replay post
i have questions ,
– Are you reading just PL 200-105 or you have another dumps ?
– When i download PL 200-105 it just about 280 questions so where another questions.
– Do you have a VCE-PLUS dumps , i think it’s a best one

Hi guys,
passed today icnd2
Had OSPF/EIGRP/GRE sims,just like here but different answers.All u need is show run and show ip route commands.
The adjasted file is still valid 80%
Had some new q’s,don’t remember them,so study your material…
Studied from: CBT NUggets,9tut and a few different sites.

Thanks 9tut for a great info

@tre1972
Which statement about slow inter VLAN forwarding is true?
A. The VLAN is experiencing slowness in the point-to-point collisionless connection.
B. The VLANs are experiencing slowness because multiple devices are connected to the same hub.
C.The local VLAN is working normally, but traffic to the alternate VLAN is forwarded slower than expected.
D.The entire VLAN is experiencing slowness.
E. The VLANs are experiencing slowness due to a duplex mismatch.XXX

@Pl413r, Thanks man. Are you sure though? By the way, have you taken ICND2 yet?

this section is drying up,what is happening

I am going to attempt ICND 1 but no idea which new topics included according to new version. if someone updates me. I will really appreciate that as well.

Anonymous,
Go to cisco site and look for icnd1 exam topics,for you to know the exact topics to study for…
also look in cbt nuggets for list of videos by the topics….
finaly look for in Google for “new topics icnd1”

Sam
better kook for the new 200-105 video series in cbt nuggets,cause there’s a new topics,and you don’t need to know frame relay and netflow anymore

Thanks all for your help. Done with CCNA today with a score of 912.

Can anyone share me the best materials for AWS system ops administrator. Please let me know if you know any website or have any materials for it.

Hello guys.
I took ICND1 in the beginning of last year. I am planning to take ICND2 the end of this month. DO YOU THINK THAT WILL BE FINE? I MEAN HOW MUCH TIME USUALLY I GET BETWEEN TWO EXAMS? Thanks a lot!

Hi all, done with icnd2 and i am planning to start ccnp. Please do let me know if there is any materials

All these done with icnd2 are fake

Passed ICND2 this morning. I made a huge rookie mistake, very early on I got a Sim. I have taken Cisco tests before and I know better than this but I hit next before looking at the questions. 4 unanswered (wrong) questions right away!!! I panicked some but was able to hold it together and still pass. Thanks for the info here, the ICND2.pdf was VERY relevant!!!

Thanks for the feedback @SW!

Free 60 days updates.
We are best latest Exam question Dumps provider:
Files in both PDF & VCE Format.
Working VCE Player
All lab topologies (.pkt) to practice in Packet tracer.

DOWNLOAD Instant Now:
https://docs.google.com/document/d/1cp2vtCYSV_21JTZF9D14Ua2gHdijtZjfIDuyVT1NyJg/edit?usp=sharing

Hi Guys and Girls! Please point me to latest dumps. Are questions offered in premium membership here in 9tut sufficient?

Hi Guys and Girls! Please point me to latest dumps. Are questions offered in premium membership here in 9tut sufficient?

Hi guys, just passed icnd2, you can use show run, so Sims are easy. Few new questions(2 or 4). Vce adjusted probably have some mistakes, but still can help with this.

Are all the questions from 9tut Premium Membership?

I just passed my 1CND 1 today with 980/1000
Thanks 9tut. 85% of the question were from here. Had some questions that are not here. The simulations look the same, but you have to be very careful. Make sure you know what’s the question asking for and know which show commands you need to troubleshoot the problems. Study hard , use 9tut for revision , go for your exam you should be fine.
Good luck!
Thanks once again 9tut.

hello @Justpassed

are you studied just 9tut ( do you have a premium membership)

or you have another dumps

can you help me

Question: 12
Refer to the exhibit.
Router edge-1 is unable to establish OSPF neighbor adjacency with router ISP-1. Which two configuration changes can you make on edge-1 to allow the two routers to establish adjacency? (Choose two.)
A. Set the subnet mask on edge-1 to 255 255.255.252.
B. Reduce the MTU on edge-1 to 1514.
C. Set the OSPF cost on edge-1 to 1522.
D. Reduce the MTU on edge-1 to 1500.
E. Configure the ip ospf mtu-ignore command on the edge-1 Gi0/0 interface.

Answer in dumbs is D,E

but how can it work with Subnet of /31

please soemone respond

@Aslam

OSPF work on two types of network:

Broadcast and NMBA (non-broadcast multiple access network). The answer A is a “distraction”. OSPF USE MULTICAST to communicate with neighbors via hello messages not BROADCAST. When the neighborhood is established the communication use unicast messages to learn the network topology via LSA (type 1 to 7). Is normal associate /30 for a Ethernet broadcast connection (1 subnet address, 2 network address, 1 broadcast address) but in this case we don’t need the broadcast address, so /31 is a valid subnet range according to the neighborhood specification (SAME SUBNET). 🙂

@Aslam

typo on “NMBA” should be said NBMA

Hi Folks!!! Can anyone please tell me the link for latest dumps?
Thanks in advance.

How can get the last dump for icnd 2 please help me

Hello @Tracy Liang your dumps just 283 questions about icnd 2 , so where are another questions , you talked 402 … ?????

Hi ..just passed my exam got 9XX .. thanks for every one 9TUT…there was about 8 or 9 new QUESTION and very hard Simulation of Eigrp , Ospf and GRE but if u have done enough practice you will be fine.. Adjusted VCE or icnd2PDF is still valid though..

i remember there was one new question about DTP Default mode.
1) on
2) off
3) desirable
4) auto

there was something about STP root port and option were
!) HELLO
2) Packets
3) Segments
4) BPDUS

@Caan
Thank you for post , i have a question , what dump reading before exam

@aynax i study all the dumps available in thin link but give more time to icnd2pdf and adjusted vc. cause they got right answer

https://www.dropbox.com/sh/2imx6rougqnla2z/AAAMR_KERfE6fEJy0GYILEQYa?dl=0