Share your ICND2 Experience

@ dude… i downloaded it and could only see the 1st 5. I have never used the vce thing before do you have to register and pay to get the rest? Out of the 1st five one of those I saw on the icnd2 on 9/6

anyone knows if updates to the site will be coming soon? I had maybe 3 or 4 questions from this site and testking and actualtest…everything else about 90% was new

when did you take the test dave? I am scheduled for tomorrow in the AM

@TJ I took it yesterday and there was 1 question from this site on there and it was the MAC address one in operations

There is a actualtest from the 31st of Aug that had about 5 or so.

guys HONESTLY i’ve been searching the need for a week now. no sites offer updated dumps. don’t even look. I made them show me some questions and these are not valid honestly just week for a week or two they might update. I’ve posted the latest actualtests.com dumps these are not valid and they say they’ve updated it august 31st. well it’s not true.. the test-king huh I guess they are buying from each other.
http://www.examcollection.com/cisco/Cisco.CertifyMe.640-802.v2010-08-03.by.Winget.360q.vce.file.html try this one .. it has alot of valid icnd2 questions eventhough it’s ccna

@tester u need full exam engine .. it’s called virtual exam suite.. u can torrent or find cracks easy on the net just google it k…
take care as I’m very drunk

I passed ICND2 today. I don’t want to be an alarmist because they annoy me, but the exam has really changed. There were a few new sims on my exam today. I barely passed (830). The only SIM on this site that would be close was the subnetting one. There were a lot of questions that were modified to be ‘trick’ questions of questions I’ve seen from dumps. For example, the “What would happen?” questions, the answers were the “Works properly” answer, instead of what you would expect (i.e Router WAN link not in proper subnet, blablabla). If that makes any sense. The only way I passed was because I learned the material from the ground up, I don’t look at any dumps until the day before the test. The latest dumps on examcollection are decent, there are a few “very similar” questions (IPV6, some others).

The sims: I had one questioning details of frame-relay. This one was similar to 9tut. (The one with “Which interface uses default encapsulation?”) Then there were some new ones about configuring a new switch for vtp, vlan access, etc. Time was not a factor, though there were way more questions that required careful reading and thought. The way I see it, ICND1 are basic networking concepts, either you know it or you don’t. It’s a good “entry level.”

This is the most important: ICND2 you have to know more than just definitions, you have to know what everything does, what layer it works on, what does it look like if it breaks, and how do you fix it. Most important is “WHAT DOES IT LOOK LIKE IF IT BREAKS.” Also, lots of questions on routing tables, know OSPF/EIGRP routing/topology tables, what they look like, how to interpret it. Know it cold. NAT was mostly conceptual questions. A few on “What should this ACL look like?” Spanning tree a bit too, not much though. Mainly understand root path, etc, all the concepts regarding STP. Also had a RSTP compatibility question.

To study: CBTNuggets ICND2 course (probably the most fun/easy way to learn the basic gist of the material), Odom’s ICND2 book – review questions, TONS OF PACKET TRACER – SHOW COMMANDS, IMPLEMENTING EVERY CONCEPT, ETC., ExamCram CCNA quick reference card at the beginning of the book is awesome for last minute review.

Onward and upward….

Hey Guys,
Just came from the testing center and barely passed with an 851, passing score was 825 (40 questions). I passed ICND1 on August 20 so I studied hardcore for ICND2 for almost 3 weeks.

I had exactly everything that Middz (August 27 post) had on his exam.
Lots of Diagrams – OSPF, EIGRP, Subnetting, STP, Frame Relay, ETC…

Study Material –

CBT Nuggets ICND2 – went through each video at least 5 -7 times each.
Purchased 3 routers (from ebay $20 each 2600 and 2800 series) and used 4 of my switches from my workplace (2950 and 3550 series) to create the same lab as Jeremy has in the Nuggets. This is probably the best thing you can do for practice.

9tut helped a great deal, I learned alot of by going through the ICND2 and CCNA labs/sims/hotspots.

Nice little quick review before going in http://packetlife.net/library/cheat-sheets/

The last week before the test I went through all of the newest dumps out there – Pass4sure, Testinside, TestKing, Actual Tests- 640-802 & 640-816 I had all the most current versions (end of August and Sept. Updates) I can tell you that the dumps that claim to be updated in August and September do not have many questions that are on the test. I only had about 10 questions that came from all of these dumps and they were not even exact. It’s still a good idea to go through these dumps though to get an understanding of the concepts, if you understand the question and answer then you will do fine no matter what the questions are. If you are looking to memorize the questions and pass the test then you should wait until the new valid dumps come out.

I can say this was a really tough test and I under-estimated the difficulty of it, I finished my last MCITP EA exam back in June and thought that series was tough until I took ICND2.
I think I focused way to much on the configurations and not enough on concepts like IPV6 and RIP, I had about 4 questions on IPV6 and I was clueless because I didn’t think it was important.

This exam was very condensed and you really need to know your stuff. I will try to remember more of the questions and will post later if I can come up with anything.

Good Look all

TJ – congratz for passing dude.
lol I failed the exam also skipped the ipv6 cuz I didn’t think it’s important but anyway.
I think dumps are ok for use but I wouldn’t rely on them.. after all why do u get certified if you are about to memorize all the stuff. – That way I’ll get certified for C++ and I have no clue about it. I like networking and I wanna know it.
I’m going to sit the exam after two weeks and then do some microsoft certs. I think it’s worth it.
how long did u study for MCIPT EA ?
all the best

Thanks dude. MCITP took me about 6 months total to complete all 5 exams. It was a long process.

I took the ICND 2 today and the exam was completely different from this website. Nothing was the same but you really shouldn’t pin all your training on dumps. You have too study and understand and you will be alright. I found this test pretty tough compared to the ICND 1 exam. Got a 975 on 1 and a 878 on 2. Good luck to you all.

hey guys take a look at this site..

@CASAY: TRY THE DUMP PLZ AND LET US KNOW IF ANY FROM THESE DUMPS WERE IN THE TEST
http://www.examcollection.com/cisco/Cisco.Braindump.640-816.v2010-09-05.by.W1zard.312q.vce.file.html

i took it tuesday and failed..i can verify if this is legit or not, but I only get 5 questions in trial version…how do i get the full version…try googling…did not find any free crack

http://hotfile.com/dl/47875913/2e5ea9b/Backup250110-2.rar.html
download it and install it … the .reg file is for registration. close visual exam and then run that .reg.

@ dude. I just went through all of those questions and only saw about 10 that look familiar. My memory may be a little weak but everything else looks like it is from the old dumps still.

I wanna say that these dumps are unfamiliar to me too but i think there are so many dumps that will cover anything if u read the explanation.

Dude, as TJ says..only a few about 8 that look familiar from the exam.

Hey guys,

Glad to see people are passing from my posts. Again, I’m not sure how much has changed in the past few weeks since I took it, but the two times I took the exam it was largely the same. The materials I referenced above are what got me through it. ‘Course, actually studying and reading the books the good ol’ fashioned way is always my recommendation.

@faisal

never mind the latest dumps, use whats on this site to clarify your understandings of cisco and study. Thats the best way, not trying to remember the questions and answer.

Whats the point in just waiting for new dumps before you sit your exam?

you’ll sit the test and pass get a job and wont have a clue what your doing.

took the exam today had one question from all the dumps on here: Operations Question 1 and it was slightly different

none of the other questions or sims listed here.

Had 1 config sim VTP: setting up a switch as a client in a already established VTP domain.

consisted of: giving the switch a vlan 1 ip, setting DG, setting as vtp client, and setting domain name and of course saving the config 😉

then rest of the sims i had where just “show sims”

Had about 4 ipv6 questions, a tonne of OSPF questions & STP, EIGRP, FRAMERELAY

passed with 850, pretty sure i got every ipv6 question wrong as i never bothered to study it

@Rakeim and why already passed exam.
Hey guys. Why passed exam and remembered what kind question about IPv6, Just identify which address vavid and which not valid? Or give a defenition abot Unique Local address, IPv6 anycast and unicast address, link local address etc? Maybe in dumps present same questions?
Guys, please help. I will pass exam on next week. Best wishes!

@miko from memory there were actually 5

1. What are valid addresses? with a list of addresses
2. How is ipv6 transferred to ipv4? tunneling, hashing…something along those lines
3. types of “casts”?, eg anycast, unicast, multicast
4. what kind of addresses can be assigned to a host? unique local, link local, global , something like that.
5. something about what does link local address consist of? i knew they began with FE80 and there was an option for that so pretty sure i got that one

i guess you need to just know the fundamentals

this one is almost spot on

“1. Configure Switch with the following to communicate with the other Switch (trunking already configured):
A. VTP Client Mode
B. VTP Domain Name
C. IP Address for Native Vlan (Vlan1)
D. IP Default-Gateway
”
It was

A. assign the new switch the last usable ip in the management subnet
B. assign the new switch the correct Default-Gateway
C. set the new switch to be a VTP client
D. Set the new switch to be part of the existing VTP domain

you get access to swith A (already in vtp domain) and Switch B (new switch)

First thing i did, go to the existing switch- Switch B

SwitchA#show vtp status — to find out the vtp domain which was “metic”

swithcA#show run — to find out the DG and what the management subnet is in my case was 192.168.188.61 255.255.255.240 (so in the .48-63 subnet)

A. went to switch B

Switch#conf t
Switch(config)#vtp mode client
Switch(config)#vtp domain metic
Switch(config)#ip default-gateway [DG from the running config of switchA]
Switch(config)#interface vlan 1
Switch(config-if)#ip address 192.168.188.62 255.255.255.240

i then did a show vtp status (to ensure it vtp is working) and tested pings to dg and switchA

and finally of course remember to do

Switch#copy run start

@RAKEIM

What were other LAB/Sim in your exam besides VTP ?
any drag and drop ?

Rakeim sanx for your perfect answer, respect from my side.
Guys help please why knowing full answer. Question from IPv6 is following:
what kind of addresses can be assigned to a host? unique local, link local, global ,etc.

Took it today and couldn’t believe that my score was only 900 as I am almost a CCIE. Now, after looking at this blog, I see that this VCE file DOES have some of the MOST DIFFICULT questions in it. Specifically, look at 113. That was there and the question is retarded because default-information originate is not an ICND 2 topic for OSPF. The official study materials mention nothing about it. Apparently it can cause a routing loop? Coudn’t confirm that one anywhere online, so I plan to try it out myself! Worst part of this exam is the extreme lack of time…

I almost think Cisco was F’ing with me because I swear there was not one single EIGRP question!

OK all total I counted 3 questions in that VCE file that are on the real thing. So good luck people!

@STA, Congr…

what kind of LAB SIM you got on the exam ?
any question do u remember ?

@ umer

* VTP config Sim
* a show sim for Framerelay – with 4 questions
* a show sim for ospf – with 4 questions
* Drag n drop OSPF & EIGRP – https://www.9tut.net/icnd2/icnd2-drag-and-drop-questions-2
* Drag n drop ACL building

@STA i agree time factor is the biggest issue, best thing to do when you get the 15 minutes for the practice exam and survey, jot down your table

eg

prefix /25 /26 .. ….
Value 128 64 …………
mask .128 .192 . ………
Wildcard .127 .63 ……………..
No of SB 2 4 ………..

Makes life a hell of a lot easier

And what question 113? which VCE file are you referring to there’s about 10 on this blog

This VCE file:
http://www.examcollection.com/cisco/Cisco.Braindump.640-816.v2010-09-05.by.W1zard.312q.vce.file.html
Yes I got the VTP sim which couldn’t have been easier…
I did not get a FR sim, I did not get an OSPF sim
typical drag and drop of subnet masks for VLSM
drag and drop of routing features like hold-down timers, poison reverse, etc
one that threw me off is what does an Inactive PVC mean? (remote end issues)

Again the things that freaked me out were the CCNP questions thrown in (I have a CCNP).
Such as the default-information originate question (113) and a question regarding DR election for OSPF.
And again, not one single question on EIGRP, which makes me wonder if I got a different exam somehow because Cisco knows I already have the cert.

I have a vested interest in seeing others pass, and so I retake the exams every 6 months just for fun, to make sure I’m training others appropriately. Am I really supposed to start mixing in these advanced topics?

Oh, sorry for so many posts, but I just remembered that I had at least 10% questions asking about STP Bridge ID’s and OSPF router-id’s. So know those elections inside and out (lowest ID for STP, highest for OSPF).

@STA

i had that question not too sure what you mean “Such as the default-information originate question” Default information originate is covered in ICND2 material. Its in the book and in CBT nuggets

The question is a bit of a trick question as the router advertising the “default-information originate” is configured wrong

its default route is to send it back in to the lan “ip route 0.0.0.0 0.0.0.0.0 Serial 0/0” serial 0/0 is the LAN interface it should be serial 0/1

hence

“Any packet (originating from R2 or from a network attached to R2) destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.”

It’s not in the “official” material i teach… And even if it is in the examine objectives the part about it causing a routing loop sounds mistaken anyway. I’m pretty sure split horizon would keep a packet from entering the router and then traveling back out the same interface. This is why you need subinterfaces for frame relay and intervlan routing, because a packet isn’t supposed to go right back out the interface it came in on. Either way my point is that it’s too advanced.

@STA 100% correct split horizon should be stopping this, so it technically it isn’t routing loop.

i take back what i said 😉

Split horizon is disabled by default if you are using the physical interface
Split horizon is enabled by default if you use sub-interfaces. You manually have to turn off

so the question and answer is valid

Hi everybody. I read all the posts. Conclusion: we don’t have a sure dump for icdn2 exam anymore at this moment, isn’t it?

I’m a little bit confused… 🙁

nope .. there’s no such dumps out for the moment

I have downloaded a bunch of dumps and after reading this entire thread, looks like there are no more dumps out there.
I guess the only way to prepare is to study (which I have been doing) and do a couple of the supposedly “newer” dumps as practice to prepare.
I am taking my exam end of this week.
Any suggestions/last minute tips?

@ STA
hey guys, got the same question on my exam, answered the one with routing loop.
And I think that split horizon cannot run on any of links-state routing protocols including OSPF.

@ STA & FRED..

The correct answer is routing loops.

It has nothing to do with Split Horizon or even any routing protocols.

The router has a configured default gateway for 0.0.0.0 0.0.0.0 out the serial interface that sends it back to the other router. It will send it to the last router it just came from. Once that router receives it will send it back.

When the first router receives the packet it will look at its routing table and see a static route for 0.0.0.0 and send it. The originating router would see it and then look at its routing table and send it back to that last router because it is the route for 0.0.0.0. The questions is trying to trick you into thinking it really has something to do with OSPF or some sort of routing protocol when really it is all based on the default gateway that was given to the router.

Took test today and failed. Had 40 questions and all except for maybe 5 where new questions (not listed on here or in actualtests) Studied hard and for awhile and disappointed in outcome not sure where to begin studying again for retest. Though I really understood the concepts. I think a little had to do with me second guessing my self with the new questions.

only 5 new questions? or only 5 from here?

@dude It seems he lived the same bad adventure as Sergio (read his post, only 5 from here).

I’m going for ICND2 this Fri. I have done alot of studying, we’ll see how it goes!

im doing tomorrow @ 10am NZ time. lets hope this site has helped.

Time to say goodbye to dumps I guess.

Passed today. 40questions
50% were from dumps (crazyhunter/acme/mashti)
5-6 Drug n Drop
simlets- Frame Relay and OSPF
lab- VTP
studied CBT, CISCO Press and doing dumps to find out my weak sides

THANX for all sharing your experience
Good luck!!

PS IP addresing in lab has some trick. Use first AVAILABLE ip address (real first was Default Gateway, next- Vlan1 of switch 3. and I used third addr in subnet.)

@ccent-ccna so i deduce dude’s actual test ver 1.9 is very good, 50% are covered, or maybe more, isnt’it? can you check pls? maybe the combination of at1.9 & last p4s & last Testking is enough to cover all or quite all the questions, ya? labs in this site are good too ya?

@amerigo: testking and actualtest are exactly the same 1.9 lol
hope to see real dumps over here

@ CCENT-CCNA:
What does acme and mashti mean?

I have my exam tomorrow, I can’t get the VCE files to open.
Where can I get a free download of the VCE manager?

Passed the ICND2 today. 40 Q’s. I felt they threw everything they could at me…well, ospf, eigrp, a switch set up, access list set up…had 4 drag and drops…fun stuff. The sims were different than the ones posted here. The sims posted here however, do help some. I studied with cbtnuggets and the official ICND2 book from cisco. I went over some old dumps 2 days before the test. Did nothing the day before. The best way to pass is to actually learn and fully understand the material. Even thought it was 40 Q’s, I finished with 3 seconds left. And I left the last sim half assed since i had 4 q’s left with 1 minute to go. passed with a 878.

http://www.examcollection.com/640-816.html

Also, stop asking for the latest dumps. Just learn the damn material and use this site as reference/study material. Great site 9tut.

E
Asking for dumps does not mean that someone hasn’t learnt the material.
It’s just a way of knowing the kind if questions that come.
Ive been hearing the test has gotten significantly harder, so wanted an idea of the level of hardness.
I’ve been prepping for 4 months now.

Hi all,

anyone knows what happen to 9tut.com site?

Thanks in advance

Renny

@E Hitler is death. Go to hell with him. Here reigns the freedom and i’m free to ask everything. You wanna help me ok, on the contrary SFTU. You are ZERO.

I mean cbt nuggets and more practice questions
Sorry abt the typos

@N, Time is indeed the biggest factor. congratz. @amerigo – lol nerd rage

i cant open ccna website tell me what is the problem
http://www.9tut.com
when i open this site i received this message

this account has been suspended

tell me pls what is the problem

why 9tut.com has suspended any other way to open this site.

@N

Congr!!!!

What did you have on SIM/LAB ?
any IPV6 Questions ?

Hi all,

site http://www.9tut.com seems operating few minutes ago…. after blocked a redirect to other site without any original contents of 9tut….

anyone knows what happen?

Thanks in advance

Renny

Failed today w/ a 811 passing 825, missed it by half of a question. time is definetly a factor. OSPF routing got me stuck for longer than I expected. Oh well that’s how it goes. Also ran out of time, had 10 questions w/ 10 mins to go. Best advice is to get route sumarization down and how the route will look in the routing table. I studied CBT nuggets and went through dumps 1.9 and the one by wizard. They are good but you really need to focus on the concepts, how to apply them and what it looks like when something is not working. This site is good for practice but the test itself is hard and time is a factor.

Oh yeah, I was going for ICND2

I’m not looking for any dumps, just going to study hard and try again. Had the vtp setup switch 2 by comparing it to switch 1 to get domain. Simlet on eigrp and ospf. Route summary. IPv6 think I passed that. Access-list drag and drop. Nat questions. but the harder questions seem like they were borrowed from the ccnp test because it was not covered in Icnd1 or Icnd2 of cbt nuggets. what can I say about this test, if you don’t passed it the first time at least you will get a good idea of what’s on it.

@ B Hi. Could you remember what questions were in this simlet about EIGRP?
Anybody still didn’t mention it up until that time.
About what sim from ccnp which has caused at you the greatest difficulty, you remember though some questions? Any new difficult questions? Thanx.

@PASSED ICND2 today, My experience

I got SIMS, (1LAB and 2 SIMS)

1st LAB (VTP Configuration Lab) Scored 100

Configure Switch with the following to communicate with the other Switch (trunking already configured):
A. VTP Client Mode
B. VTP Domain Name
C. IP Address for Native Vlan (Vlan1) (I had 1st assignable address from SW1 Range)
D. IP Default-Gateway (Same as SW1)

2) Frame-Relay SIM (100% Score)

Same as 9TUT, But they were asking something different this time, different IP address, and Different map ip address and Dlci

3) OSPF SIM

Topology
R1–>connected to ISP (Area 0/1), R1–>connected to R2, R1—>connected to Fast Ethernet Switch1, again R1–>connected to FastEthernet Switch2, SW1 and SW2 both connected to R3 and R3 connected to R2

Question: 1) What is the router ID
Answer: The highest ID was the link b/w R1 and ISP,(area 0/1) and i know it is correct, no matter it is connecting to ISP

Question 2) How R2 and R3 Load balance traffic
Answer: OSPF Cost, OSPF Bandwidth (2 choices)

Question 3) How R2 and R3 maintened relationship or something like any message are going to pass after establishing neighbour relationship
Answer: Hello 10 seconds

Question 4) How many route are R1 has as OSPF
Answer: I had 4 Route, 2 conencted through SW1,SW2, other were ISP and R2

4 to 5 IPV6 Question (new)
2 to 3 New drag and drop never found in any dump (new)
ACL Drag and drop (9tut)
6 to 7 OSPF question (new)
3 to 4 EIGRP Question (1 found in dump others were new)
5 IP Subnetting questions ( 2 found in actuall test latest version, others were new)

I Studied CBT Nuggets, Train signals, Todd lemme, and Cisco official certification guide.
Scored 937

only 10 to 11 question were from the latest dumps, if you rely on dumps you will be fail, learn the concept and practice again and again. watch videos, time limit is a factor……..

It is very hard exam now, even you cant rely on 9tut for ICND2.

Thanks to Allah I passed and thanks 9tut, MIDZ and fenderpass ( I have very similar paper )

@umer great job, mate. Congratz. Please could you do one thing for us? Yuga and fender said that the questions we complain cause we cannot find are all here in this quite old actualtest version: http://www.4shared.com/get/eYIpvaKd/AT_640-816_v080609.html

Can you download it and check how many of your exam questions are present there, please?

tnx in advance

@amerigo thanks……
you can give me your email address i can send it to you

takecare

i just failed the ccan (640-802) today with an 809 out of 825. none of the sims from here were on the test..

the only one i struggled on was the one for nat/acl where you have to prevent computer b from accessing a finance server on another network through a router.. you are not given any ips for any of the servers or computers (just the last octet for the comptuers) and have to figure out all the ips on your own by guessing ips for each server (which are in the subnet of the server networks router interface) and then test each one within a internet explore window when you click a pc…

by the time i figured out what the hell was going on i was already over 25 mins into the sim and this was the 2nd question so i freaked..

@amerigo,

I have the same actuall test and i found nearly 15 to 16 question were present on the test….
Best of luck
let me know if some body need a help

Yes it is good, but it is not enough to pass the icnd2

@umer

15 to 16 questions present in the old Actual Test. Interesting.

What about the combination of old Actual Test and newest Actual Test (dude’s version, that is AT1.9)?

I think with this combination we can reach a maximum of 70% of real exam questions. (labs excluded, 9tut for them).

And i bet if i add the last Pass4sure or/and the last CertBrain, the maximum will go to 80/90% as well, that is 30/32 questions on 40 total.

@amerigo,

15 to 16 question were included in old actual test with 472 question
the new version may contain 4 to 5 question only which was drived from 472 question as well

more than 60/70% question on ICND2 test were new (never found in any dump yet)

Do not rely on dump.

guys the latest of ccna 640-802 has some questions included in real exam
actually alot. also with my actualtest there can be lots of good combination.
after all u need to learn ok. i’m taking the exam by the end of the month.
I have talkted to actualtest they said they are gonna update it.
I’m gonna post it as soon as they update that dump.
best of luck

@umer

I’m not relying in any dump, but if i can take the exam knowing already 70/80% of questions, why i should have to renounce?

Old AT2009 = 15/16 question = 40%

New dude’s AT 1.9 or more (i hope soon) = 10 questions (and not only which was drived from the old one) = 20%

Do you know the last CertBrain? The Form D has 103 new questions that AT does not have.
many ppl said many questions were from there. I’m not able to write the right percentuage, but we can see that we already know more than 70% of real exam questions (labs excluded. See 9tut or the posts above for it).

And i’m not considered pass4sure or Testinside or TestKing because i’m waiting anyone matching his/her experience with that dumps.

Finally,despite of what you said, more than 60/70% on icdn2 are known and dude, Yuga, fender and others can confirm it.

It would be enough to take the exam, obviously studing as well and not only knowing the dumps, but, as i said before, if i can take the exam knowing already 70/80% of questions, why i should have to renounce?

All the people they are reading me right now are here to find out dumps and not only books to study. So stop with all this false morals and be honest, at least one time.
I’m not pointing you, umer. I’m talking as “general purpose”.

@DUDE
very well mate. I’m waiting you for AT, even if we need the last testking/testinside as well. Can you do something?

@dude
the latest 640-802 dump has “some” or “a lot” icnd2 questions? how many as percentuage terms?

@ Amerigo
Could you give information about location link new CertBrain with new 103 questions? Where is this dump hide? Thx.

@miko

hi miko, the correct name is BrainDump and not CertBrain as i wrote. Anyway, you can find it here: http://www.examcollection.com/cisco/Cisco.Braindump.640-816.v2010-09-05.by.W1zard.312q.vce.file.html

@amerigo,

actualtest with 472 question may contains 14 15 questions, but if your concept are good, and you understand what they are asking, u will surely pass, but as i said ICND2 is changed now…..

best of luck

@ amerigo
I am already drilling this dump 🙂
So, in this moment we have 2 valid “so-so” dumps with 472 and 312 questions, correct ?
I as well can recomend for you this site
http://www.ciscolab.ru
Present 5 blocks for ICND2 each 55-57 questions- on-line tests. It is old site, many same questions with AT e.t.c, but I found many questions which are absents in all dumps, for example about IPv6. I am 100% for sure.
One problem- it is russian site and you must regestrit on it (not difficult procedure).
On-line tests on English lenguage, in section “онлайн тесты”. For me it was good training.
Good luck.

Hey guys. At whom English language not native, should add additional 30 minutes, correctly ? Still it is not enough of it for this purpose that not strongly would care of time?

The previous question intended who already passed the test or tried to passed.

@umer

can you check this dump as well, please?
http://www.examcollection.com/cisco/Cisco.Braindump.640-816.v2010-09-05.by.W1zard.312q.vce

How many questions of your exam taken you found it that they are not the same than actual test?

@miko
yes, that’s correct.
More, it is enough in my opinion. Most of the questions you will already know, so all this time are just for the new ones.

@miko

let me know the result of your drilling!!! 😉

@ amerigo
Uki duki. May be on next week I wiil try pass, still didnt for sure.

I contacted Pass4Sure and they said they will update their ICND 2 dumps late September.

I’m constantly checking their website but no updates yet.

Keep writing guys and Ill keep reading, gotta get my ICND 2 outta the way, but due to the posts lately I’m not attempting the exam till these new dumps come out. I don’t have the money to throw into the wind.

Thanks to all of those who keep us informed of the exam situation.

Good luck to all of those who are taking the exam.

Take care.

811 failed. (640-816) Actually, I never seen any of simulations even here. Be carefule, guys.!!

VTP (domain changed to client) / OSPF / ACL sim

@gwbaby

I got the same score, so close, maybe missed by half of a question.

FYI, 640-802 (not sure code) Dump for CCNA (not ICND1, ICND2) is still valid. but ICND series dumps are no longer valid.

Hey Droid,

Have you heard anything back from P4S?

GWbaby is correct. The sims I saw were all new.. of the Wizard dump I think maybe 15 questions are on the test.

I have contacted both Pass4sure and Actualtests asking when the updates are due.
Will update everyone when I hear from them. Both say that the last update was done on 31st August, but obviously some others have confirmed that the exam wasn’t out of those questions.

I wanna ask the people who have sit this exam (ICND 2). What topics should we focus on more than the others. I have been doing CBT Nuggets, but see that a lot of stuff is not from there. Do others feel the same way…I don’t really wanna read “Wendell Odoms” 600 pages book even though I own it..

Apparently, this site claims that theirs was updated yesterday http://www.ciscoexams.org/640-816-icnd2-2/. Can someone with subscrition download it and then put it on RAPIDSHARE for someone else to perhaps verify??

they link leads u to passguide .. and in their official site they say they last updated the dumps on 28nd august 2010.
so it might be the script that runs in that site which updated the date automatically.
best of luck

Hi dude,

Can you please answer my other questions as above…

@Matty
Hey matt how’re u?
well honestly the sims are pretty easy ( I had the one with switches where u have to configure the switch2 by reading the configuration of switch 1) it’s in this site aswell.
also be focused on:
How would a routing table look like from EIGRP/OSPF.
router summarization, some access-list but pretty easy ones aswell.
I have failed on Route (scored 44%) on that and I know why.

IP ROUTING questions from this dumps are valid:
http://www.examcollection.com/cisco/Cisco.CertifyMe.640-802.v2010-08-03.by.Winget.360q.vce.file.html (note it’s a ccna dump)

I had many of these questions on my exam, and if I had this dump before I would’ve passed.
also the drag and drop about EIGRP/OSPF from this site was on my exam.
best of luck to all

I have a actualtests.com subscription and I’m waiting for them to update the dumps and I’ll post here.

Best of luck.